СвязьПроект

Российский системный интегратор
Текущее время: 27 апр 2024, 19:30

Часовой пояс: UTC




Начать новую тему Ответить на тему  [ Сообщений: 5 ] 
Автор Сообщение
 Заголовок сообщения: Bridge AP2640-Wi-Fi-AP2640
СообщениеДобавлено: 10 апр 2008, 05:45 
Не в сети

Зарегистрирован: 10 апр 2008, 04:33
Сообщения: 2
Приветствую.
Была дана задача реализовать вынос номеров по IP.
Дано: Офис0 (ATC Samsung iDCS-500 с городскими линиями) - AP2640 (16 FXO) - Wi-Fi bridge (две точки доступа, объединенные в мост) - AP2640 (16 FXS) - Офис1.

Задача реализована, но есть определенные проблемы:

1. При поднятии трубки звонящего телефона в Офисе1 идет сплошной гудок (т.е. идет обрыв). Эта ситуация повторяется как при звонке из Офиса0, так и при звонках с города. В логах АТС отчетливо видны обрывы (длительность звонков в 3-5 сек, что не нормально).

2. Как следствие из п.1, должным образом не обрабатывается переодресация (такие же отбои).

3. При наборе номера с выходом на город из Офиса1 слышны гудки "занято". Из логов АТС видим, что не полностью набирается номер, например вместо номера 9-8-902-1234567 набирается 9-8-902-123567. Естесственно такого номера нет.

Самое забавное, что тенденцию обнаружить не получается ни на одной из 3 проблем. Хаотичность объяснить логикой не реально. Таким образом то отбои идут, то их нет (первый, второй звонок отбились - а третий нормально); с набором номеров такая же ситуация, то нормально набрался, то неполностью.

Для решения таких проблем были предприняты следующие действия:

1. Настройка сигнала занято (FXO)
(config)# voice class clear-down-tone 0 450 0 500 500

2. Увеличение задержки времени ring detect-timeout (до 7 секунд).

3. Слышимость BACKRING еще до установления связи с FXO/

4. Танцы с бубном вокруг частотности тон-сигналов для максимального comunity железок и АТС.

Все эти танцы и махинации практически решили проблему с отбоями (по крайней мере их стало значительно меньше), но вот проблема неполного набора номера так и осталась.

Может кто-нибудь сталкивался с подобной проблемой. Буду благодарен за советы.
Сразу оговорюсь - проблемность Wi-Fi можно откинуть. Проверял не раз - Wi-Fi work properly.

Конфиги прилагаю:

AP2640_FXO# sh run
!
version 8.30N
!
hostname AP2640_FXO
!
!
no bridge spanning-tree
!
ip route-cache
!
!
no ip-share enable
!
!
interface ether0.0
ip address ххх.хх.х.х 255.255.255.252
!
interface ether1.0
ip address ххх.хх.х.х 255.255.255.252
!
snmp name AP2640
snmp enable-trap dn-register 300 forcely-block
!
no arp reset
!
route 0.0.0.0 0.0.0.0 ххх.хх.х.х
!
utilization cpu
!
logging event all
logging on
!
remote-log interval 1
remote-log primary-server ххх.хх.х.х
remote-log secondary-server ххх.хх.х.х
!
ntp refresh 600
ntp offset 05:00
ntp server ххх.хх.х.х
!
!
!
!
!
! VoIP configuration.
!
!
! Controller configuration.
!
!
!
! Voice service voip configuration.
!
voice service voip
fax protocol t38 redundancy 0
fax rate 9600
h323 call start fast
h323 call channel early
h323 call tunnel enable
timeout t303 8
timing dtmf-duration 100
no local-ringback-tone
remote-log primary-server ххх.хх.х.х
remote-log secondary-server ххх.хх.х.х
remote-log interval 1
!
!
! Voice port configuration.
!
! FXO
voice-port 0/0
connection plar 300
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 0/1
connection plar 301
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 0/2
connection plar 302
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 0/3
connection plar 303
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 1/0
connection plar 304
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 1/1
connection plar 305
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 1/2
connection plar 306
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 1/3
connection plar 307
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 2/0
connection plar 308
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 2/1
connection plar 309
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 2/2
connection plar 310
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 2/3
connection plar 311
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 3/0
connection plar 312
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 3/1
connection plar 313
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 3/2
connection plar 314
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXO
voice-port 3/3
connection plar 315
ring detect-timeout 70
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
!
!
! Pots peer configuration.
!
dial-peer voice 100 pots
destination-pattern 100
port 0/0
!
dial-peer voice 101 pots
destination-pattern 101
port 0/1
!
dial-peer voice 102 pots
destination-pattern 102
port 0/2
!
dial-peer voice 103 pots
destination-pattern 103
port 0/3
!
dial-peer voice 104 pots
destination-pattern 104
port 1/0
!
dial-peer voice 105 pots
destination-pattern 105
port 1/1
!
dial-peer voice 106 pots
destination-pattern 106
port 1/2
!
dial-peer voice 107 pots
destination-pattern 107
port 1/3
!
dial-peer voice 108 pots
destination-pattern 108
port 2/0
!
dial-peer voice 109 pots
destination-pattern 109
port 2/1
!
dial-peer voice 110 pots
destination-pattern 110
port 2/2
!
dial-peer voice 111 pots
destination-pattern 111
port 2/3
!
dial-peer voice 112 pots
destination-pattern 112
port 3/0
!
dial-peer voice 113 pots
destination-pattern 113
port 3/1
!
dial-peer voice 114 pots
destination-pattern 114
port 3/2
!
dial-peer voice 115 pots
destination-pattern 115
port 3/3
!
!
!
! Voip peer configuration.
!
dial-peer voice 300 voip
destination-pattern 300
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 301 voip
destination-pattern 301
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 302 voip
destination-pattern 302
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 303 voip
destination-pattern 303
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 304 voip
destination-pattern 304
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 305 voip
destination-pattern 305
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 306 voip
destination-pattern 306
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 307 voip
destination-pattern 307
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 308 voip
destination-pattern 308
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 309 voip
destination-pattern 309
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 310 voip
destination-pattern 310
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 311 voip
destination-pattern 311
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 312 voip
destination-pattern 312
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 313 voip
destination-pattern 313
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 314 voip
destination-pattern 314
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 315 voip
destination-pattern 315
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
!
!
!
!
!
gatekeeper
!
!
! Gateway configuration.
!
gateway
h323-id voip.ххх.хх.х.х
no ignore-msg-from-other-gk
!
!
! Codec classes configuration.
!
voice class codec 1
codec preference 1 g726r32
codec preference 2 g726r16
!
!
!
! SIP UA configuration.
!
sip-ua
!
!
! MGCP configuration.
!
mgcp
codec g711ulaw
vad
!
!
! Tones
voice class clear-down-tone 0 425 0 500 500
!
voice class dial-tone 425 0 10000 0 0 0 -12
!
voice class line-busy-tone 400 450 500 500 0 0 -12
!
voice class reorder-tone 425 0 300 200 0 0 -12
!
voice class line-lock-tone 425 0 100 100 0 0 -12
!
!

AP2640_FXS# sh run
!
version 8.30N
!
hostname AP2640_FXS
!
!
no bridge spanning-tree
!
!
no ip-share enable
!
!
interface ether0.0
ip address ххх.хх.х.х 255.255.255.252
!
interface ether1.0
ip address ххх.хх.х.х 255.255.255.252
!
snmp name AP2640
snmp enable-trap dn-register 300 forcely-block
!
no arp reset
!
route 0.0.0.0 0.0.0.0 ххх.хх.х.х
!
utilization cpu
utilization ethernet
!
logging event all
logging on
!
remote-log interval 1
remote-log primary-server ххх.хх.х.х
remote-log secondary-server ххх.хх.х.х
!
ntp refresh 600
ntp offset 05:00
ntp server ххх.хх.х.х
!
!
!
!
!
! VoIP configuration.
!
!
! Controller configuration.
!
!
!
! Voice service voip configuration.
!
voice service voip
fax protocol t38 redundancy 0
fax rate 9600
h323 call start fast
h323 call channel early
h323 call tunnel enable
timeout t303 8
timing dtmf-duration 100
timing fxo-offhook-duration 100
timing fxo-onhook-duration 100
no local-ringback-tone
inband-ringback-tone
remote-log primary-server ххх.хх.х.х
remote-log secondary-server ххх.хх.х.х
remote-log interval 1
!
!
! Voice port configuration.
!
! FXS
voice-port 0/0
connection plar 100
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 0/1
connection plar 101
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 0/2
connection plar 102
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 0/3
connection plar 103
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 1/0
connection plar 104
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 1/1
connection plar 105
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 1/2
connection plar 106
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 1/3
connection plar 107
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 2/0
connection plar 108
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 2/1
connection plar 109
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 2/2
connection plar 110
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 2/3
connection plar 111
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 3/0
connection plar 112
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 3/1
connection plar 113
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 3/2
connection plar 114
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
! FXS
voice-port 3/3
connection plar 115
low-dtmf-gain -3
high-dtmf-gain -3
no caller-id enable
!
!
!
!
! Pots peer configuration.
!
dial-peer voice 300 pots
destination-pattern 300
port 0/0
!
dial-peer voice 301 pots
destination-pattern 301
port 0/1
!
dial-peer voice 302 pots
destination-pattern 302
port 0/2
!
dial-peer voice 303 pots
destination-pattern 303
port 0/3
!
dial-peer voice 304 pots
destination-pattern 304
port 1/0
!
dial-peer voice 305 pots
destination-pattern 305
port 1/1
!
dial-peer voice 306 pots
destination-pattern 306
port 1/2
!
dial-peer voice 307 pots
destination-pattern 307
port 1/3
!
dial-peer voice 308 pots
destination-pattern 308
port 2/0
!
dial-peer voice 309 pots
destination-pattern 309
port 2/1
!
dial-peer voice 310 pots
destination-pattern 310
port 2/2
!
dial-peer voice 311 pots
destination-pattern 311
port 2/3
!
dial-peer voice 312 pots
destination-pattern 312
port 3/0
!
dial-peer voice 313 pots
destination-pattern 313
port 3/1
!
dial-peer voice 314 pots
destination-pattern 314
port 3/2
!
dial-peer voice 315 pots
destination-pattern 315
port 3/3
!
!
!
! Voip peer configuration.
!
dial-peer voice 100 voip
destination-pattern 100
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 101 voip
destination-pattern 101
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 102 voip
destination-pattern 102
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 103 voip
destination-pattern 103
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 104 voip
destination-pattern 104
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 105 voip
destination-pattern 105
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 106 voip
destination-pattern 106
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 107 voip
destination-pattern 107
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 108 voip
destination-pattern 108
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 109 voip
destination-pattern 109
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 110 voip
destination-pattern 110
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 111 voip
destination-pattern 111
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 112 voip
destination-pattern 112
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 113 voip
destination-pattern 113
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 114 voip
destination-pattern 114
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
dial-peer voice 115 voip
destination-pattern 115
session target ххх.хх.х.х
voice-class codec 1
dtmf-relay h245-signal
no vad
!
!
!
!
!
!
gatekeeper
!
!
! Gateway configuration.
!
gateway
h323-id voip.ххх.хх.х.х
no ignore-msg-from-other-gk
!
!
! Codec classes configuration.
!
voice class codec 1
codec preference 1 g726r32
codec preference 2 g726r16
!
!
!
! SIP UA configuration.
!
sip-ua
!
!
! MGCP configuration.
!
mgcp
codec g711ulaw
vad
!
!
! Tones
voice class clear-down-tone 0 425 0 500 500
!
voice class dial-tone 425 0 10000 0 0 0 -12
!
voice class line-busy-tone 400 450 500 500 0 0 -12
!
voice class reorder-tone 425 0 300 200 0 0 -12
!
voice class line-lock-tone 425 0 100 100 0 0 -12
!
!
Заранее спасибо


Вернуться к началу
 Профиль  
Ответить с цитатой  
 Заголовок сообщения: Re: Bridge AP2640-Wi-Fi-AP2640
СообщениеДобавлено: 10 апр 2008, 12:33 
Не в сети

Зарегистрирован: 18 май 2007, 07:59
Сообщения: 55
debug rta ipc
debug voip call

можете прислать?


Вернуться к началу
 Профиль  
Ответить с цитатой  
 Заголовок сообщения:
СообщениеДобавлено: 14 апр 2008, 05:21 
Не в сети

Зарегистрирован: 10 апр 2008, 04:33
Сообщения: 2
Странно, может я чего-то непонимаю, но перечисленные команды ничего не выводят, либо что-то не так....

По-сути, разбираясь с вопросом, пришел к выводу, что вышеописанная проблема появилась из-за того, что на АТС после первой и второй цифры набираемого номера стоит пауза, то есть, если набрать 9 8 909 и т.д. то набирается 9 (пауза 2 сек) 8 (пауза 5 сек) 909 и т.д.
Фишка в том, что почему-то Addpac, хоть я и поставил паузу между набираемыми цифрами, эти паузы не делает, или если и делает, то уж точно не такие как я задавал при настройке...

Может кто знает команду задания паузы только между конкретными цифрами. Например, в АТС можно задать нужные паузы после любой цифры. А в Addpac я нашел, пока, только команду tidt, но она задает паузу между всеми цифрами...


Вернуться к началу
 Профиль  
Ответить с цитатой  
 Заголовок сообщения:
СообщениеДобавлено: 14 апр 2008, 06:48 
Не в сети

Зарегистрирован: 18 май 2007, 07:59
Сообщения: 55
Что бы делать какие-то выводы надо посмотреть отладку.

AP(config)# deb-port - Для вывода отладки.


Вернуться к началу
 Профиль  
Ответить с цитатой  
 Заголовок сообщения:
СообщениеДобавлено: 14 апр 2008, 07:25 
_mag_ писал(а):
Может кто знает команду задания паузы только между конкретными цифрами. Например, в АТС можно задать нужные паузы после любой цифры. А в Addpac я нашел, пока, только команду tidt, но она задает паузу между всеми цифрами...


Попробуйте между цифрами в номере поставить запятые. При запятой цифра не будет набираться 1-у секунду. Или уберите паузы на АТС.


Вернуться к началу
  
Ответить с цитатой  
Показать сообщения за:  Поле сортировки  
Начать новую тему Ответить на тему  [ Сообщений: 5 ] 

Часовой пояс: UTC


Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 0


Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете добавлять вложения

Найти:
Перейти:  
Создано на основе phpBB® Forum Software © phpBB Group
Русская поддержка phpBB